How to Reconstitute Peptides With Bacteriostatic Water
Updated November 8, 2026
Reconstitute peptides by injecting sterile bacteriostatic water into a vial of lyophilized powder, using the ratio recommended on the label or your source. Common ratios are 1 ml BAC water per 5 mg of powder, but always check first. Gently roll the vial until dissolved, never shake. Store reconstituted peptides in the fridge.
Why Bacteriostatic Water
Peptides ship as lyophilized powder to stay stable at room temperature. To inject them, you need to add a solvent. Bacteriostatic water (BAC water) is sterile water with 0.9% benzyl alcohol added as a preservative. It stops bacterial and fungal growth once the vial is open, so your reconstituted peptide stays good longer. Reconstituted peptides in regular sterile water deteriorate much faster.
The benzyl alcohol also prevents peptides from sticking to the vial walls during reconstitution. Use BAC water every time for injectable peptides.
Finding Your Reconstitution Ratio
The reconstitution ratio tells you how much BAC water to add per milligram of powder. Common ratios are 1 ml per 5 mg (5:1), 1 ml per 10 mg (10:1), or 2 ml per 5 mg (2.5:1). You need to know this before you start.
Check the label on your peptide vial. If it does not say, look at your source's product page or call and ask. Common peptides have standard ratios: BPC-157 is usually 2-3 ml per 5-10 mg vial, and TB-500 is typically 2 ml per 10 mg. Use the StackCal dosage calculator to verify your dose after you mix.
Reconstitution Steps
Gather a sterile 1 ml syringe, a sterile needle, your peptide vial, and a bottle of bacteriostatic water. Work on a clean, flat surface. Do not need to be sterile yourself, but do not contaminate the needle or syringe tip.
Draw up the exact amount of BAC water you need into your syringe. If you are mixing a 10 mg vial of TB-500 with 2 ml of water, draw 2 ml. Wipe the rubber stopper on the vial with an alcohol pad and let it dry for a few seconds.
Slowly inject the water into the vial. Angle the needle so the water hits the side of the vial, not a direct stream into the powder. This prevents foaming and bubbles. Do not inject air into the vial unless you drew some in by mistake.
Gently roll the vial between your palms for 30-60 seconds until the powder fully dissolves. The solution should be clear. Stop if you see particles floating or the liquid stays cloudy. That usually means the powder was degraded before you got it.
Let it sit for a minute. Some peptides take a moment to fully hydrate. Once clear, you are done. Write the reconstitution date on the vial with a marker and store it in the fridge.
Worked Syringe Math Example
You have a 10 mg TB-500 vial mixed with 2 ml of BAC water. You want to inject 2.5 mg (2500 mcg). How many units on a U-100 insulin syringe?
First, figure out the concentration: 10 mg in 2 ml = 5 mg/ml. You want 2.5 mg, which is half the vial. Half of 2 ml = 1 ml. On a U-100 syringe, 1 ml = 100 units. So you draw to the 100 mark.
Another example: 5 mg BPC-157 mixed with 2.5 ml water = 2 mg/ml. You want 250 mcg (0.25 mg). Formula: (dose_mg ÷ (vial_mg ÷ bac_ml)) × 100 = (0.25 ÷ (5 ÷ 2.5)) × 100 = (0.25 ÷ 2) × 100 = 12.5 units.
Use the insulin syringe units guide if this does not make sense. Most people write the concentration on the vial after mixing so you do not do this math every injection.
Common Mistakes to Avoid
- Shaking the vial: Shake makes bubbles and can damage the peptide. Roll gently instead.
- Using regular sterile water: It has no preservative. Reconstituted peptide goes bad in a few days. Always use BAC water.
- Touching the needle or syringe tip after it is clean: Even one finger ruins sterility. Once it touches something non-sterile, use a fresh needle.
- Injecting air into the vial: It is not dangerous, but it makes the vial harder to work with as you draw up. If you accidentally pump air in, use a needle to let it back out.
- Storing reconstituted peptide at room temperature: Bacteria and fungus grow fast without refrigeration, even with benzyl alcohol. Keep it cold.
Storage and Shelf Life After Mixing
Reconstituted peptides stay good in the refrigerator for 14-30 days depending on the compound. BPC-157 and TB-500 both last 30 days in the fridge. Some peptides like CJC-1295 no DAC last only 14 days. Check the details for your compound or ask your source.
Do not freeze reconstituted peptide once it is mixed. Freezing breaks down the molecules. Keep it in a regular refrigerator between 2-8°C. If it gets cloudy, smells off, or you see particles, throw it out and start fresh.
FAQ
- Can I use regular sterile water instead of bacteriostatic water?
- Technically yes, but your peptide will degrade much faster. Regular sterile water has no preservative, so bacteria and fungus start growing the moment you open it. Reconstituted peptide in regular water lasts maybe 3-5 days in the fridge, not 14-30. Use BAC water.
- What if my reconstituted peptide gets cloudy or has particles?
- Do not use it. Cloudiness usually means the powder was already degraded, or the water was contaminated. Particles can indicate bacterial or fungal growth. Throw it out and make a fresh batch.
- How do I know if I mixed the right concentration?
- Use the StackCal dosage calculator to check. Enter your vial size in mg, the amount of BAC water you added in ml, and your target dose. The calculator shows you how many units to draw on a syringe.
- Can I use a different reconstitution ratio than recommended?
- You can, but stick to the recommended ratio. Mixing with too little water makes the solution thick and harder to draw up; too much water dilutes the dose per unit and wastes vial space. Most ratios are optimized for both accuracy and storage.
- Do I need to heat or cool the water before mixing?
- No. Room-temperature BAC water works fine. Do not heat the vial. Peptides are temperature-sensitive and heat can damage them. Cold water from the fridge is fine too.
Compounds in this guide
Information only. Not medical advice.